Pneumatic Push in Fittings

Misting Fittings, Push-in Misting Fittings, Push to Connect Misiting Fittings

Write a commentPush Connect Misting Fittings

Advantages:

1) Tubing could be installed and uninstalled easily without hurting tubing.

2) Proof Pressure is 490psi (3.5Mpa)

In the video, we used a nozzle with 0.5mm hole, pressure at 250psi (1.8Mpa) for testing.

 

3/8" to 3/8" Push to Connect Fitting Union Straight

1 Comment3/8 to 3/8 Push to Connect Fitting Union Straight

PU 3/8 - 3/8" push to connect fitting union straight is used to connect two tubes of 3/8" O.D in the same direction. Release collar and Lock-claw built in the 3/8" push to connect fitting union straight allow easy connection and disconnection 3/8" tubing without using tools and causing damage to the tube.

Push-in Tubing O.D: 3/8"
Fluid Admitted: Air, Vaccum, Water(no freezing)
Body Material: PBT
Seal, O-ring: NBR
Working Pressure: 0∼1.0MPa | 0∼150psi
Proof Pressure: 3.0Mpa | 435psi
Negative Pressure: -100Kpa | -29.5 In Hg
Working Temperature: 0∼60°C | 32∼140°F
Lock Claw: Stainless Steel(SUS)
Applicable Tube: PU / PA / PE / PVC

For more information, please go to https://www.wellfittings.com/composite-push-in-fittings-for-metric-inch-tubing-pt-r-bspt-connection-thread/pu-union-straight/pu-3-8-3-8-o-d-tube-union-straight-push-to-connect-fitting.html

M7 Thread Male Connector Push in Fitting, Push to Connect Fitting

1 CommentM7 Thread Male Connector Push in Fitting, Push to Connect Fitting

M7 thread male connector push in fitting, push to connect fitting from Pneuflex could match 4mm, 6mm, 8mm, 10mm, 5/32", 1/4", 5/16", 3/8" O.D size tubing.

https://www.wellfittings.com/composite-push-in-fittings/composite-push-in-fittings-for-metric-inch-tubing-pt-r-bspt-connection-thread/

316L Inox Push in Fittings from Pneuflex

1 Comment316L Inox Push in Fittings

Pneuflex designed and promoted high quality 316L stainless steel pneumatic tube fittings for customers. FDA certificted so can be used for food equipments. Using viton O-ring inside of the 316L inox push in fittings for sealing.

Easy installation and disconnection without any tools: pushing the tubing into fittings to be gripped to connect the Pneuflex tubings. When removing tube tubings, pressing the release sleeve and pulling the tubings out of the fitting.

Stainless Steel Transition Fittings

Write a commentStainless Steel Transition Fittings

Pneuflex 's 316 stainless steel transition fittings are used to connect soft nylon, polyurethane, polyethylene or Teflon tubing one one end and metal tubing on other end. The soft tubing connection end is stainless steel push to connect fitting configuration, and the metal tubing connection is double ferrules stainless steel compression tube fitting configuration. Both push to connect fitting end and compression tube fitting end are made of 316 stainless steel. Stainless steel transition fittings are suitable for use with air, water, oil and steam in high temperature and wash-down applications. Accommodate metric tubing O.D ranging from 4 mm to 16 mm, inch tubing O.D ranging from 1/8" to 1/2".

STPC union straight stainless steel transition fittings are designed to connect sot tubing on one side and metal tubing on other side in the same direction. Detail information, please refer to https://www.pneuflex-pneumatic.com/stainless-steel-transition-fittings/stpc-union-straight/